Why Nobody Cares About Nissan Qashqai Key Fob

Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai's bigger dimensions give it an SUV-like feel. Its 19-inch alloy wheels on Ti and STL models may also be firm. The front tyres in the Qashqai may also lose grip on rough surfaces and the CVT could occasionally show wrist-flexing torque steering.

This is usually due to an unresponsive coin battery that can be replaced in just a few minutes. Make sure the new battery is of the same voltage, size and specification.

Water Damage

One of the most common reasons a Nissan key fob displays the "key ID incorrect" message is due to water damage. The key fob has rubber seals that protect the chip inside. However, prolonged exposure to moisture can cause it to cease functioning properly. It's normal to see this when your key fob has been dropped into the water or a swimming pool. However, it can occur when it's wet from rain or soapy hand.

If your key fob was exposed to water over many years then you might need to clean it using isopropyl or electronic cleaner. It could also require to be sent to a professional for repair or replacement.

If your key fob requires to be replaced, it is an easy process. Make sure you have the right multipack (CR2032, 3V). Then, open the front and back cases with the small flathead screwdriver. You'll need to take out the clips for retaining metal and pull out the old battery, then replace it with the new one. After reassembling the fob put the mechanical key back in place and verify that it is working correctly. If it isn't it, you'll need to bring it to a Nissan dealer or professional auto locksmith to repair the chip in the key. Fortunately, the chip is not normally damaged by exposure to water, so this should not be a major expense.

Dead Coin Battery

The coin battery is a second common reason why your Nissan Qashqai remote key fob won't work. These batteries last 3-5 years, but they can become faulty over time when the fob is dropped often. You could try replacing the battery with a fresh one but be sure it's the same size and voltage as the original. If you choose to use an alternative battery, it could cause the key to have an invalid key ID which will prevent it from pairing with your vehicle.

The best way to replace the battery in a Nissan Qashqai key fob is by prying open the fob with an small screwdriver that has a flat head. The screwdriver needs to be inserted into a small notch at the bottom of the key fob. Make sure to gently twist the screwdriver to break the two halves. Remove the old CR2025 battery and replace it with a brand new one, taking note of the location of the old one within the fob.

Before you put the new battery into place, make sure there is no dirt or water damage on the terminals. If not clean the terminals using some isopropyl ethanol. You'll also need to make sure the pole cables are connected correctly - they should be connected to the negative and positive poles of the battery.

Troubleshooting

If your Nissan Qashqai key fob stops working after exposure to clean tap water or rain it could be a sign of an internal chip problem. The battery replacement won't fix this, and you'll need to buy another key fob. If the key fob has stopped working after dropping it, it is likely that the chip inside was damaged. If you clean the chip using isopropyl ethanol and a paper towel, then replace it in the key fob, you will usually get it working again.

Key ID Incorrect is a typical error that you can see on the dashboard of your vehicle. This means that the vehicle is unable to recognize the key fob and will not allow it to start the engine. The issue can be caused by a variety of factors such as water damage, undetectable faults in the circuitry of the key fob, or RFID interference.

If the battery that powers 12 volts on your key fob is empty or isn't supplying enough electric power, it will stop working. This will affect the remote keyless system as well as central locking in your Nissan Qashqai, as well as stopping you from starting your engine with the key fob (if equipped with Intelligent Key). If you're unable to lock or unlock the door manually you must check the batteries on the key fob to make sure they are in good condition. Try reinstalling the battery to reset your transmitter.

Reprogramming

If the key fob was not submerged in saltwater the device should be able to come back to life with a simple rinse of clean water. You can also clean the electronic chip by using isopropyl or electronic cleaner. If none of the above works it is possible to replace the key fob.

If your Nissan Intelligent Key still does not function, there may be a problem with the connection between it and the vehicle. To reconnect it, begin by turning the key in the ignition without starting the car. Continue this process until the hazard light flashes two times. Then, turn off the vehicle and remove the key.

Open the fob compartment of your vehicle's fob compartment. It's usually in the door jamb, on the handle of the driver's side or under an armrest. Find the small button labeled "program" and press it. You will hear a sound after the process is completed.

It's time to test your Intelligent Key to the test. You must stand a certain distance away from the vehicle, then hit all the buttons on it. If the lights flash and the horn sounds this means that the key has successfully linked to the Nissan. You can also test it near the Nissan.