7 Small Changes That Will Make The Biggest Difference In Your Upvc Win…

UPVC Window Handle Replacement

Replacing a damaged or broken window handle is a easy task and, with the right tools, it can be accomplished quite quickly. But it's essential to identify the type of handle and its spindle's length prior to purchasing an alternative.

Older uPVC windows use cockspur handles for windows. They have a spur that protrudes to the lock of a wedge cockspur striker plate. They can be left- or right-handed and must be matched when replacing.

What type of lock and handle do I have?

There are a myriad of window locks and handles made from upvc each with its particular advantages and uses. The type of handle you choose will determine if your locking mechanism is efficient and if it is easy to open windows. With time and regular use, the upvc handles on your windows can be damaged and worn out. This makes them less secure and effective. In some instances, they could even fall off completely. If you notice that your upvc window handles have fallen off, it's essential to fix them as soon as possible. This will help to prevent potential break-ins and ensure your home is secure.

Luckily, replacing your window handles made of plastic is a relatively simple task that can be completed by almost everyone. You'll need some basic tools, but with the right knowledge, it is a straightforward process that should only take a few minutes. It is important to know the type of lock or handle you have on your window. This will help you choose the right replacement.

Inline Espagnolette Handles

They are typically located on the side of the window. They are flat and feature an open latch that is connected to the locking mechanism of the window frame. Inline upvc handles also come with spindles that run through the middle of the handle and into the frame of the window to activate the latch.

Cockspur Handles

These handles are usually found on older uPVC window frames and have a distinctive, hook-shaped design. Cockspur handles are fitted with a single screw that holds the handle to the window frame and aren't as secure as other kinds of window handles.

Handles that turn and tilt

The tilt and turn handles are different from other upvc handles because they can be rotated for opening the window, and then tilted into the window to ventilate. In general, they have a 7mm spindle at the side of the handle. They are available in both left and right handed versions.

When purchasing replacement handles made of upvc it is essential to verify the length of the spindle since not all of them are identical in size. Drop something into the middle of the hole to check the length. This is the length of the spindle that will be suitable for your window.

What is spindles?

uPVC window handles work in a similar manner as doors. By turning the handle, you can operate a latch within the frame. The window can then be opened and closed. However, UPVC Window Handle Replacement sometimes these handles can become damaged, especially when they are used frequently or exposed to extreme weather conditions. This can lead to the need to replace your uPVC windows handles as they may not be able to operate the window in a proper manner for a long time.

There are several different types of uPVC handles to choose from, comprising Espag, Cockspur and Spaded handle options. These handles are designed in a variety ways to fit into uPVC frames. Each handle style uses an entirely different spindle for locking the window mechanism. This is why it is essential to know what type of handle you have installed on your uPVC window to get the correct replacement for it.

You can check what type of uPVC handle you are using by looking at the base section of the handle. There should be a "snap in cover' over one screw which holds the handle base in place. Take it off and you should be able see the second screw at the opposite end of the base section of the handle. After both screws are removed and you are able to pull the handle from the uPVC.

Once you have removed the uPVC window handle, you will need to carefully unscrew the spindle that was previously attached to the locking mechanism. Note the length of the spindle. You will need to buy a replacement of the same length as the handle that was originally used and locking device.

The primary issue with uPVC window handle problems is that the spindle gets worn out and can no longer operate the locking mechanism. This can be due to damage from constant use or loosening of the locking mechanism, or even corrosion that occurs over time. If this happens, it is required to replace the window handle and the locking mechanism to restore the full functionality to your uPVC windows.

How do I take off the handle from the previous one?

In the course of time and daily use, window handles may become damaged or broken and if this happens it is essential to fix them as soon as possible to ensure the security of your home. It is good to know that replacing a worn or damaged handle is a relatively simple task that can be completed in less than an hour and doesn't require any specialist tools.

To remove the old handle, first remove the screw that is located at the base of the handle. Once the screw has been removed, the handle will be removed. There will be another screw located at the bottom of the handle's base and it is able to be removed too. After both screws are removed, the handle can be removed from the base of the window.

After removing the old handle and fixing holes, align the holes of the new handle with the existing holes in the window frame. There may be a tiny cap or sticker on the new handle, so take off these if necessary and then screw the handle into the frame. It is crucial to verify that the handle works once it is put in place. Turn the handle over and make sure the lock mechanism is in place.

Espag handles feature a spindle which protrudes from the handle and slot into the multipoint locking mechanism that is on the window frame. Cadenza windows feature blades with cut-outs that slot into the lock mechanism, while Cockspur handles have a long nose that is able to hook over either the frame's outer or transom bar cross-member inside the window.

Once you have installed the new handle, place the spindle inside the glass window replacement lock and tighten it. Replace the snap-in cover and screw cap (if appropriate) after the handle is securely fixed. The handle is now ready for use, so try opening and closing the window a few times to make sure that it is working properly and securely.

How do I fit the new handle?

The process of changing your window handle made of uPVC isn't a big deal and the process is simple. You only need a screwdriver and a little bit of patience. The first thing you need to do is make sure that the handle you have previously used is in the unlocked position and then remove any screws that are visible. you can also replace these with screw caps if needed. After removing the handle you'll need to take note of the length of the spindle which extends from the back. This is important as it will determine the type of handle you'll need to buy.

Espagnolette handles that are made of uPVC are the most popular kind of handle. The spindle passes through the handle to control the locking mechanism inside the frame of the window. Once the handle is turned it opens the latch on the window and allows it to open. Over time and through regular use, espagnolette handles could be damaged or destroyed and it is necessary to locate an alternative.

Cadenza handles are another type of uPVC window handle, which is typically used on tilt and turn windows. They have a protruding blade that operates an interlocking mechanism that is multipoint within the window. They are usually more secure than espagnolette handles as they are only accessible from the inside. They can be replaced using the same procedure as you would with espagnolette handles, but make sure the new handle is angled and not flat.

Once you've decided on the correct handle to purchase You can simply place the new handle with the existing screw holes, and then screw it into the appropriate position. Then, you should put the screws on and test the new handle. This is accomplished by moving the handle from the locked position to the unlocked and then back to the locked position a few times. If you have any issues, it could be beneficial to speak with a professional to determine if they can assist in resolving the issue. They are often able to advise you on the best approach to resolve the issue in a speedy and effective way.