The Worst Advice We've Ever Received On Fiat Panda Key Fob Replacement

Reasons Your Fiat 500 Key Fob Won't Work

A key fob for fiat punto key replacement 500 makes it easy to open doors and start your vehicle. There are many reasons the key fob might stop working. This includes a dead coin-battery, water damage, receiver modules issues, and interference.

This listing is for a NEW replacement Fiat Flip Key Remote - like the Ilco brand that must be programmed professionally by a local automotive locksmith (click here to search for a Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the main cause of your 500 key fob not functioning. Modern key fobs have a restricted operating range, and must be within a few feet of the car to operate. If you are further away from your vehicle, and you press the keyfob button it will not respond, and display the message "Key Fob Not Detected".

If this occurs then replace the battery for your coin-cell (Part Number CR2032) by a fresh one of a reliable brand, such as Panasonic Duracell or Energizer. You can find them in your local hardware store or online.

After you've replaced the battery of your coin cell It is possible to test it by standing next to your fiat Panda key fob replacement [samkwang.eowork.co.kr] 500 and pressing the buttons. The parking lights will flash and the key fob should operate the lock and unlock switches.

If the fob's key doesn't work after replacing the battery, it may have water damage that prevents it from connecting to the receiver module inside your vehicle. Water damage can happen in a variety of ways, ranging from small splashes to submerging the fob salt water at the beach. If you think your fob was exposed to water, place it in a bag of rice to draw out the moisture. If this does not work, you'll need to have your fob replaced by an auto locksmith or dealer.

Water Damage

While the fob has some rubber seals to keep water out of the chip's electronic circuit and out of the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to short and eventually cease to function. It's not the best idea to get the fob wet however, but don't give it up when you accidentally drop it in water, or fail to remove it from your pocket.

First, remove the battery from the fob. Before replacing the battery, clean the electronic chip with isopropyl or a similar product. Next check the fob to see if it works. If the key still doesn't work, it may need to be reprogrammed. This is typically handled by a dealer or professional auto locksmith.

If the key is a newer model and was not programmed to your car It will most likely need to be replaced completely. This is an easy process that can be carried out by a professional automotive locksmith. The locksmith needs to cut the key to match the ignition in your vehicle. They'll also have to reprogram the fob to your car's system. This is a simple and cost-effective process that can be completed in the same day.

Receiver Module Issues

Your 500 key fob might not work because it's out of range. The remote has a maximum range of 30 feet, so should you be too far away from your vehicle it will not respond to your commands. This can be easily fixed by moving closer to your vehicle until it starts responding.

If you've replaced the battery in your coin (commonly called a "button" or "watch") and the fob won't work, it could have an internal circuit board problem. In most cases, reprogramming the fob can resolve the issue. You can find the instructions for the majority of vehicles on YouTube or in the owner's guide.

It is possible to replace the metal clips that hold the coin batteries in the correct position. If they lose tension it can prevent the battery from being seated properly and cause the remote to malfunction.

In rare cases the fob might become desync'd with your vehicle due to software or hardware issues. You can fix this problem by visiting your local dealer or auto-locksmith to reprogram your key fob. In some cases it is possible that the software will require reinstallation in your body control modules.

Interference

Interference can also cause the key fob not to receive or transmit an signal. This may happen if the keyfob is located in close proximity to a radio transmitter, like a cell phone or radar detector. The key fob could not function because of a problem to the buttons or water damage, or damage to the internal chips.

If your key fob suddenly stopped working, or if you've tried everything at home to solve the issue (e.g. replacing the battery, reprogramming it and using the spare key fob, it could have a faulty receiver module on your 500. The receiver module is located under the dash and receives the radio frequency signals from the key fob. It transforms the signals into electronic commands, which are then read by the vehicle.

There is a straightforward method to reset the 500's internal system, including the keyfob. Disconnect the 12 volt battery for about 15 minutes by taking off the negative cable first then the positive cable. Reconnect the battery. This will clear any residual electricity, and allow you to restart the computer of your car. This will help you get your key fob to function again. If the issue continues you should seek out a certified technician. They can identify the exact cause of problems.