What Peugeot Keys Experts Want You To Be Able To

Peugeot 208 Key Replacement

Peugeot 208 key replacement is best left to professional auto locksmiths who have the proper equipment and know-how. They can create and program keys faster and less expensive than dealerships.

If your key fob has stopped locking or unlocking your doors, it is likely due to a dead coin battery. There are many other reasons why the key may be malfunctioning.

Dead Coin Battery

A dead battery in the coin compartment will stop your Peugeot 208 from locking or unlocking, and cannot start the engine. If this is the case, you'll have to make use of the backup starting procedure which is explained in the owner's manual of your vehicle.

The spark plugs may also be worn out. The spark plugs ignite fuel to start the engine. However they have a short time of life. They'll eventually degrade when they aren't used enough.

There is an easy solution to this problem. Verify the voltage of your battery using a multimeter. If the voltage is less than 11,5 volts then it's time to replace it. It is also important to clean the contacts of the battery if it has corrosion. This can be accomplished by taking off the rubber covers from the two battery terminals, and then using a wirebrush, you can remove any parts of the battery that are corroded. Then, reconnect the cables for the positive and negative poles.

Water Damage

If your 208 doesn't start and the battery isn't running, then make sure that the spark plugs work. You might find that they're filthy and don't spark. The spark plugs can be cleaned in the workshop.

Peugeot automobiles use a transponder key that is compatible with the car's immobiliser system. This makes sure that only the correct key can turn the engine. If the chip inside the Peugeot key is damaged, then it will not transmit the proper signal to the vehicle.

Water damage is the most common cause of this problem. This is a common issue in warmer climates where the vehicle is exposed to rain or snow. If this is the case, you should call a reputable auto locksmith who has all the tools and equipment needed to change the key's programming. They also have the most up-to-date technological know-how and machinery required to create the Peugeot 208 smart key. The process shouldn't take more than 15 minutes.

Faulty battery contacts

Peugeot replaced the old transponder chips with a new model that is based on electronic components that are mounted on a circuit board. This new system works great when it's fresh, however, over time, the circuit boards start to deteriorate and stop working properly.

This could stop the immobiliser from working, so your vehicle will not start. If this happens, it's a good idea call a Peugeot specialist or locksmith.

A common issue occurs when the battery inside the key fob starts to die. This causes the blade of the key to stop feeding into the lock. A locksmith from your vehicle can replace the battery and cut a fresh blade for you, it's normally a quick fix.

Faulty Receiver Module

It could be that the receiver module has a problem if your Peugeot key fob isn't working after being dropped on the floor, exposed to a sudden storm or accidentally washed. The receiver is responsible for sending radio frequency signals to the on-board computer which controls the centralized locking system in your Peugeot vehicle.

The key fob itself is fitted with rubber seals to prevent water from reaching the electronic chip inside. However prolonged exposure to water may cause damage to these seals and the chip. Submerging the key fob into ocean water at the beach or throwing it into the water can be especially damaging because of the high salt content.

If your Peugeot spare key fob isn't working it is necessary to have the module replaced. This can only be done by a Peugeot specialist or expert auto locksmith. peugeot key replacement keys like other cars are secured by an immobilizer device. This requires the right coding to start the car. This is the reason why you should only go with a knowledgeable Peugeot locksmith with the task of designing and programming an alternative.

Computer on board is not working properly

The on-board computer of your Peugeot is responsible for a variety of systems in your car, including power windows and airbags. The on-board computer will show the code when something goes wrong. The code is stored within the system and will stay there until the problem is solved. Often, this will involve the on-board computer being replaced.

One of the most common reasons for the airbag light flashing is loose or corroded connections in the airbag sensor. This could be due to wear and tear, aging, or exposure to salt and moisture. This issue needs to be dealt with as soon as you can, because an airbag that's malfunctioning could be dangerous in the event in the event of an accident.

If your Peugeot is showing a card detected as not present error, then the battery in the key fob may be weak or dead. This will stop the key fob sending a signal to deactivate the immobilizer on your vehicle. Test this by pressing the unlock key on the fob's key and then trying to start your vehicle. If it doesn't work it is because the battery of the key must be replaced.