15 Pinterest Boards That Are The Best Of All Time About Lock Repair

Door Lock glas repair window shield repair (http://newitem.co.kr/bbs/board.php?bo_table=free&wr_id=137590) - How to Fix Common Problems

If a lock doesn't latch properly is a clear indication that it's in need of being repaired. The testers at CR use lipstick to mark where the latch meets the strike plate; tightening the hinge screws could fix the problem.

Spraying a dry lubricant, Repair Window such as powdered WD-40 or graphite powder on the lock's cylinder could also help.

Check the Latch

The latch is the bolt that extends into the door door lock Repair (mariskamast.net) frame to secure the lock when it is pulled back by the handle or knob. Deadbolts and latches with positive locking are popular options for double Glazed window repairs additional security. If the latch does not close or latch properly, it could be caused by a misalignment between the strikeplate and latch in the door frame.

The most common reason for Repair window this is hinges that are loose. They can sag with time and cause the latch to fall off its strike plate. Make use of a lipstick test to test. Apply some lipstick on the edges of the latch and then attach an edging strip on the strike plate. Close the door and you'll see where the latch touches the plate. This will let you know whether the point of contact is too high or low to allow proper operation.

You'll require an entirely new strike plate in the event that the latch is more than 1/8" too high or low. Fortunately, this is an easy task that can be done without the need to remove the door. You'll need a filing to enlarge the strike plate hole. Half-round files are the best because it is in line with the contour of the strike hole in the plate.

Once the strike plate is repositioned, you'll need to tighten the screws that attach it to the door frame. This should be enough to allow your door to latch and close correctly. If not, try tightening the hinge screws on the opposite side of the door to see if it helps.

If the latch is out of alignment even after lubrication you will require more drastic measures. You can remove the strike plate, and then use a chisel that is sharp on the mortise of the strike plate, allowing you to move the latch upwards or downwards. You can also use a metal filing to alter the shape of your strike plate to fit better into the mortise. This is an option you may think about if your RV has many bumps and dips on the highway and you're worried that it might fall off during travel.

Make sure you check the Keyway

If your lock isn't working properly, you could be leaving your home open to burglars. The good news is that some types of door lock problems can be solved without the need for an expert. This is the case with a lock or a key that won't turn. The sooner you discover a problem, you are more likely to solve it yourself.

If your key isn't going into the lock or turning smoothly it may have rough spots that need to be filed off. Locksmiths can do this for you however it's a simple do-it-yourself project that you can try at home. Move the key around until you find a place that is causing friction. If you spot any of these spots, use a metal filing to smooth the rough areas.

A locked bolt or bolt that is jammed or latch is a different issue. This can be caused by debris or a damaged piece of key that has become lodged within the mechanism. You may try using a pin or needle to clear the debris, but it is recommended to call an expert locksmith for a more thorough examination and removal of the damaged piece.

A deadbolt that doesn't stay extended through the strike plate could be an indication of a malfunctioning lock. The screws that secure the deadbolt can loosen over time and cause it to move which makes your home vulnerable to break-ins. If the deadbolt is still shifting, you may need to upgrade the hardware.

If you are having trouble with a cylinder that doesn't move when you turn the key, your key cylinder could be stuck. If this is the case, use a lubricant to loosen it. You can also use dry lubricant or WD-40 spray to lubricate and remove any buildup. These items can be kept in a bottle that is convenient and used on a regular basis to maintain your locks. A lock that is lubricated will be more likely to last longer than one that's not.

Check the Hinges

A loose hinge could cause the cylinder of a door lock that rotates easily when the door is open but fails to lock when closed. This is a problem that can be fixed. To resolve the issue, tighten all the screws on the hinges. If the problem persists you can try adding or removing hinge'shims' to adjust alignment. These plates made of small metal are available at hardware stores or online.

Sand the edges of the hinge mortises (the slots that hold the hinges) to ensure they are flush with the frame. The latch bolt might be too high or low in the strikeplate. To find out this, put some lipstick on the latch, then put an area of masking tape on the strike plate. When you close the door the lipstick will smear the part of the tape it touches, leaving a mark that will indicate whether the latch is in contact with the strike plate above or below the hole.

Lastly, if the latch isn't working properly with the strike plate, it could be due a buildup of grime and dirt. This debris can be removed using a q-tip that has been soaked in graphite or silicone spray.

If the issue is still not solved after applying a lubricant, the lock cylinder might be jammed and need to be replaced. This is a job best left to an expert, but not too difficult for someone familiar with basic home sash window repairs. When replacing the lock cylinder, look for one that's been tested and rated the BHMA to avoid problems with the fit and finish.

Another reason that could cause trouble latching is if the hardware for the door lock is cheap or poorly made. This type of lock is likely to require more maintenance than a high-quality lock, and it might not last as long. If this is the situation, upgrading to a better lock is usually the best solution to the issue. It is important to choose a model that's classified as B or better in terms of durability to ensure it will stand up to years of use.

Make sure you check the Strike Plate

A door latch that doesn't reach the strike plate could cause a myriad of issues that range from preventing the door from shutting and latching properly to making it more difficult to open. It's not as difficult to fix as you think. Doors that are sagging, gravity, and even foundation movement can cause an error in the alignment of the latch and the strike plate. It's a good thing that simple adjustments are often enough to fix the issue.

If tightening the hinges and applying lubrication to the keyway does not solve the issue the strike plate might require moving to a new position to align with the latch. To do this, you must first take off the strike plate and mark the spot where the latch comes into contact with it. Mark this area using caulk, lipstick, or a strip of masking tape. If the mark is located below the strike plate's hole, it is a sign that the latch is hitting the plate too high, and the lower position of the strike plate can resolve the problem. If the mark is above the strike plate's hole, you can move the strike plate up little.

Once you know which direction the strike plate has to be adjusted, remove it from the frame and keep the screws in a safe place so you can replace them later. It is also necessary to apply lubrication to the keyway of your strike plate to ensure it moves smoothly.

Then, determine if the contact point of the latch is located above or below the strike plate hole. You can do this by applying paint, lipstick or chalk to the latch. After closing the door open it and see whether the mark remains visible on the latch or the masking. If the mark is located below the strike plate, this means that the latch is hitting the strike plate too low. the higher position of the strike plate will resolve the problem.

To make the adjustment, remove the strike plate from the mortise, and then expand it with a sharp knife or chisel, and a Hammer to allow the strike plate to move upward or downward to align with the latch's position. Once the strike plate has moved, test the door to make sure it closes and latches easily. After you have completed the adjustments, you are able to reconnect the strike plate to the frame of the door and fill in any old screw holes or gaps using wood filler that matches the color of the rest of the door frame.